View previous topic :: View next topic |
Author |
Message |
Mike Harrison M&M
![](images/avatars//17746167195f2dcbccd9bdc.jpg)
Joined: 03 Nov 2007 Posts: 2029 Location: Equidistant from New York City and Philadelphia, along the NJ Shore
|
Posted: Mon May 25, 2020 1:03 pm Post subject: Any electronics hobbyists/tinkerers? |
|
|
I've got a pair of Pickering headphones from the 1970s, and the cable, where it comes out of the bottom of the left ear cup, used to be protected from repeated bending (and thereby eventually breaking the wires inside the cable) by a short length of strain relief shrink tubing. (The tubing is also used to protect the length of cable where it exits the top of the left ear cup and where it enters the top of the right ear cup.) The wires inside the cable are broken only in the location first described.
Would anyone happen to have any strain relief shrink tubing laying about gathering dust? Its inner diameter looks to be about 1/8" (or 3.175 mm). I don't want to have to buy a 50-foot spool of the stuff when I'm going to need only several inches, if that.
Or... alternate suggestions would be most welcome, too!
Thanks! _________________ Mike
Male Voice Over Talent
I have taken leave of my sensors.
![](https://mike-harrison.com/vobb/voiceoverist-badge.gif) |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
SteveToner Contributor IV
Joined: 03 Oct 2016 Posts: 101 Location: LA & Sundance
|
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Lee Gordon A Zillion
![](images/avatars//98287787957ebfebbc932b.jpg)
Joined: 25 Jul 2008 Posts: 6843 Location: West Hartford, CT
|
Posted: Tue May 26, 2020 1:04 am Post subject: |
|
|
I bought an assortment pack of heat shrink tubing at Harbor Freight for about four or five bucks. _________________ Lee Gordon, O.A.V.
Voice President of the United States
www.leegordonproductions.com
Twitter: @LeeGordonVoice
![](http://www.leegordonproductions.com/images/oav_seal.png) |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
todd ellis A Zillion
![](images/avatars//12154882574e7931e681ece.gif)
Joined: 02 Jan 2007 Posts: 10479 Location: little egypt
|
Posted: Tue May 26, 2020 6:40 am Post subject: |
|
|
i've done it with heat shrink using increasingly larger, short lengths of tubing overlaid to create sort of a bubble inside the cavity. _________________ "i know philip banks": todd ellis
who's/on/1st?
![](http://i.imgur.com/VORj9un.jpg) |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Mike Harrison M&M
![](images/avatars//17746167195f2dcbccd9bdc.jpg)
Joined: 03 Nov 2007 Posts: 2029 Location: Equidistant from New York City and Philadelphia, along the NJ Shore
|
Posted: Wed May 27, 2020 5:55 am Post subject: |
|
|
Thanks, guys. I think I'm going to have to do what Lee did and buy an assortment, because it will take some trial and error to find the right combination of inner and outer diameter tubing to fit both around the cable and through the hole in the headphone cup. _________________ Mike
Male Voice Over Talent
I have taken leave of my sensors.
![](https://mike-harrison.com/vobb/voiceoverist-badge.gif) |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
|